- Extends the length of the USB cable up to 45 m (thanks to the unconnected CAT 5 / 5e / 6)
- Self-supply
- Easy installation
- No drivers required
- Ideal for cameras / printers / scanners, etc.
- Plug & Play
- Compatible with Windows 98/ME/2000/XP/7/8, Linux

Cable diameter:

• 28 AWG data line,
• 24 AWG power line,

Data rates to:

• SuperSpeed 5 Gbps,
• Hi-Speed 480 Mbps,
• Full-Speed 12 Mbps,
• Low-Speed 1.5 Mbps.

-Compatible withUSB2.0 (standardandreverse)
- Inputfor additionalpower
- The cableis made ofpure copper
-Thickness6 mm
-Gold-platedterminals
- Execution: aluminum

-Supports resolutions up to1920p
-Chipset:CH7101

Supports Quick Charge 3.0 technology

• Current: up to 3A
• Voltage: up to 20V
• Power: up to 60W

• Full Plug and Play support.
• Support for M.2 drives of all sizes - 2230, 2242, 2260, 2280, 22110 mm.
• Support for M.2 drives of all capacities.
• Use both drives simultaneously.
• Support single-sided and double-sided M.2 drives.
• Better heat dissipation from M.2 SSDs thanks to copper vents.
• Support booting from SSD card.

ATTENTION! In the adapter, you can insert B+M-key disks into both M.2 slots. It is important to check the disk parameters - i.e. whether the disk is designed for the SATA or NVMe (PCI-Express) interface and connect it to the correct slot. SATA drives are connected to the B-key slot, NVMe drives are connected to the M-key slot.

Input:

• PCI-Express interface, compatible PCI-Express version: 4.0 / 3.0 / 2.1 / 2.0 / 1.1 / 1.0a.
• Number of lanes 4-Lane, compatible with x4 / x8 / x16 PCIe slots.
• SATA connector for connecting to the motherboard when using a SATA M.2 SSD. In order to achieve the best transmission speeds, we recommend using a SATA 6G controller.

Output:

• NGFF 75-pin M-key slot for mounting the NVMe (PCI-Express) M.2 SSD.
• NGFF 75-pin B-key slot for mounting a SATA (AHCI) M.2 SSD.

Power:

• The adapter is powered directly from the PCI-Express bus, external power is not necessary.
• The dual power system gives enough power to the connected M.2 SSDs.
• The redundant power system also reduces the load on the adapter.

• SATA III
• Data transfer rate: SATA up to 6 Gb/s
• Clips
• Connector: straight / straight

• Support: up to 4K resolution at 60 Hz.
• Support: Up to 2K resolution at 60 Hz
• Support: Resolution up to 1920 x 1080 at 120 Hz.
• Data transfer rate: 21.6 Gbps
• Support: HDR
• Support: Dolby Vision
• Support: HDR10
• Support: 3D
• Cable diameter: 4.8 mm
• Support for Lip-Sync (audio/video synchronisation)
• Supports YUV 4:4:4 format
• Supports EDID 2.0 (device recognition)
• Body: Zinc
• AOC active optical cable
• Operating temperature: 0°C to 45°C
• Storage temperature: -10°C to +70°C
• Operating humidity: 5% to 90% relative humidity
• Bending radius: 10 mm

• Total Plug and Play support.
• Support for simultaneous operation of SuperSpeed USB, USB 2.0 and USB 1.1 devices.
• Corresponds to the final official specification xHCI revision 1.0 from USB-IF.
• UASP (USB Attached SCSI) support for faster data transfer in Windows 8 and later.
• Fully supports hot plug connection and disconnection of USB devices per run.
• Powering the controller and connected USB peripherals via the PCI-Express bus.

Input:

• PCI-Express 2.0 interface, compatible with PCI-Express 1.0a / 1.1 / 2.1 / 3.0.
• Number of lanes 1-Lane (x1), compatible with x1 / x4 / x8 / x16 PCIe slots.
• 1-Lane PCI-Express 2.0 bus bandwidth up to 5 Gb/s.

Output:

• 2x 19-pin internal USB 3.2 Gen 1 connector with two ports for connecting e.g. internal SuperSpeed USB reader or front USB ports on the computer case.
• SuperSpeed USB interface - USB 3.2 Gen 1 (previously USB 3.1 Gen 1 / USB 3.0).
• Compatible with USB 3.2 Gen 2, backwards compatible with USB 2.0 and USB 1.1.
• Support 5000 / 480 / 12 / 1.5 Mbps (super / high / full / low speed).
• When connected to the PCI-Express bus version 1.0 theor. transmission speed up to 2500 Mb/s.

• USB-C audio adapter
• Built-in digital-to-analog converter (DAC) outputs Hi-Fi quality music
• Input: USB-C, male
• Output: 3.5 mm TRRS jack
• Supports any headphones with a built-in microphone

Installation tool

One transmission unit and one receiving unit

• 1 x Cable CB-CMD37 Black
• 1 x Velcro/cable tie

• AUKEY CB-AL04 Black OEM Lightning - USB A cable (cable in foil pouch without cardboard packaging)
• Velcro/cable tie

• AUKEY CB-AL04 Red OEM Lightning - USB A cable (cable in plastic bag without cardboard packaging)
• Velcro/cable tie

• PCI-Express adapter with standard peg
• Low profile herring
• 2 pcs of heat conductive pads
• 50 cm SATA data cable
• Mounting material and screwdriver
• Printed installation manual
• Packed in a cardboard box

• PCI-Express controller with standard peg
• Low-profile end cap
• Multilingual manual
• Packed in a cardboard box

• USB 3.0 - SATA adapter with 22 cm fixed cable
• Printed installation guide
• Packed in a cardboard box

• USB 3.0 - SATA adapter with 22 cm long fixed cable
• Power adapter 100-240V / 12V-2A
• Printed installation instructions
• Packed in a cardboard box

• Personal computer or laptop with free USB Type-A port
• Device with USB 3.0 Type-B interface

5 x 15 x 200 mm

6,02 x 4 x 2,4 cm

71 x 44.5 x 14.3 mm

2500 x 25 mm

- Length: 4m
- Width: 16 mm

Adapter/extender length: 20 cm

Cable diameter: approx. 5.5 mm

Front with three holes (height x width: 30 x 130 mm)
Width: 483 mm